Electric Scooters For Kids

Weld Kickstand

How to build a metal welding table part three

A steel welding table is a basic necessity for any welder's workspace, since welding on a wooden surface can present a very real fire hazard. In addition, with a steel table, the welder's work clamp can be attached to it, and parts placed on the table will be electrically connected with the table's surface. This provides the advantage of keeping the work clamp and its cable out of your way while welding. Finally, building your own welding table will allow you to stand upright and place smaller projects at the right height for welding.
Following are instructions for building your own metal welding table. All of the items, with the exception of the metal plates needed for the shelves, can be found readily available at your local home improvement store. The steel plates can be purchased from a local steel supplier easily found in your local yellow pages. Expect to complete this project in less than four hours.

1.  Check your materials. Lay out the materials in your work area and check to make sure you have all requirements to complete the project. Remember safety equipment and fire extinguisher. Cut angle iron using speed square to mark miters. Check reference chart on the inside of the door of the welder ensuring you are using the right settings for the thickness of steel you are about to weld (standard on most Lincoln Electric compact wire feed welders). Test settings by welding on a piece of scrap before starting.

2.  Welding the two frames for the table top and shelf: Use the square on the outer edge, place one piece of 30-inch angle iron and one piece of 18-inch angle iron together, mitered side down and perfectly square. Attach work clamp to one of the pieces of metal. With welding face shield in place, tack weld the corners on the inside edges.
Use another piece of 30-inch angle iron and another piece of 18-inch angle iron. Repeat this step creating the opposite corner of your frame. Weld the opposite corners first to ensure right angles and a perfect fit.

Join the two sections of your rectangular frame together and tack weld the remaining corners.

3.  Welding the tabletop to the frame. Position your frame flat side up. Place one of the pieces of steel plating on top of the frame and center it. Attach the work clamp to a piece of scrap steel and lay it on top of the table. Tack weld around the plate. Do not make full welds at this point to minimize distortion caused by heat. Tack the corners and one or two tacks per side. When all tacks are complete, weld over each tack weld placing a weld with a finished length approximately 3/4-inch long. Finish welding the corners from underneath. Both shelves should be assembled the same way.

4. Squaring the shelves and attaching the first leg. Stand up one of the shelves on the long edge. Using the square to make sure it is at a 90-degree angle to the ground, attach one of the legs to the shelf with a C-clamp to hold it upright, like a kickstand on a bicycle. Position the second shelf parallel to the first and attach another one of the legs in the same manner. The shelves on welding table are 28-inches apart. Adjust that distance to accommodate your specific needs.

Place one of the legs on the bottom shelf corner and place the top of the leg in the inside corner of the table's top. Tack weld it in place. Next, weld both edges of the leg and shelf. Each weld being approximately 1-inch long. Weld each side.

5. Attach the remaining legs. Repeat step 5. Complete all welds on both sides of each leg before standing the table on its own weight.

Note: The distance between each leg is larger at the bottom of the leg than at the top.

6. Attaching the caster coupler nuts and casters. Place a coupler nut in the inside corner of the angle iron, flush to the bottom of the leg. Make a 3/4-inch weld on each side of the nut. Repeat this step on each leg. Let cool. Place a standard nut onto each caster stem as far as it will go. Place one lock washer on each caster stem and thread the stem into the coupler nut attached to the table leg. Adjust the height of the casters to level the table. Then, tighten the nuts to lock the casters vertically in place.

7. Attach the welding gun holder. With a clamp, attach the 3-inch length of steel tubing to the right front corner of the top shelf of the table (if right-handed; be sure to switch to the left side if you are left-handed). Attach it at a 45-degree angle with the front facing up to accommodate holding a welding gun. Tack weld the tube and remove the clamp. Make a 1-inch finish weld on the top side of the tube.
8.  Stand back, admire your handiwork and start on your next welding project. Painting the welding table is optional with a rust-resistant paint, but DO NOT PAINT THE TOP OF THE TABLE. You will want this to remain bare steel so metal parts placed on the table top for welding are in contact with the work. Before painting, clean the entire table with a cleaning solvent to remove machining oils. Mask off the top with masking tape and newspaper. Paint.

About the Author

Goscor ARC, one of the leading suppliers of welding and cutting solutions in Southern Africa, distributes for both Lincoln Electric Company and ESAB, the two largest welding organisations in the world

Weld $18.49 Weld

kickstand boom $9 HM-38-Z-06 kickstand boom

KSTAND PBS KICKSTAND $7.99 KSTAND PBS KICKSTAND.

kickstand boom holder $4.62 HM-38-Z-10 kickstand boom holder

Tuesday Weld $7.99 Tuesday Weld - Photo

Kickstand Extension $35.99 Kuryakyn Kickstand Extension Improves access to the kickstand Fully adjustable If used with Kuryakyn's Driver Floorboard Kits, you can access the kickstand without having to fold up the floorboard Sold each **Note: Fits Honda GL1800 Stand-Rite Kickstand Click Here for more Kuryakyn products

Chrome Kickstand $49.95 Drag Specialties Chrome Kickstand High-strength steel kickstands with a brilliant chrome finish Replaces OEM kickstands perfectly Overstock kickstand lengths are for bikes with longer suspension than stock Understock kickstands are for bikes with lowered suspension

Adjustable Kickstand $116.99 PSR Adjustable Kickstand CNC machined for a perfect fitment Feature adjustable settings Anodized chrome, black, gold or aluminum finish

INCIPIO / SYNTHETIC LEATHER KICKSTAND / AK-362 $34.77 INCIPIO - SYNTHETIC LEATHER KICKSTAND - AK-362

Aluminum Kickstand $107.99 Aluminum Kickstand Kickstand now feature a hard black oxide coating Coating hardness of HRC 60-70 gives wear resistance of case hardened steel while maintaining the weight of aluminum Light and tough with cold forged 7075 aluminum stands and CrMo pivot plates, there is no stronger kickstand on the market Custom designed with quick bolt on installation using O.E.M. mounting points

Kickstand Sunglasses $90 VonZipper Kickstand Sunglasses Hey you, get on your bike and ride! Better yet throw down the kickstand and get down to business so you can get back to the business of getting down. Ya heard? Features: 100% UV protection Base 8 spherical lens Impact resistant polycarbonate lens Nylon grilamid frame Stainless steel optical hinges

Pinch Weld Cover $148.99 Pinch Weld Cover; Powdercoat Black;

Steve McQueen & Tuesday Weld $7.99 Steve McQueen & Tuesday Weld - Photo

1 Lowered Kickstand $79.95 Arlen Ness 1" Lowered Kickstand Chrome-plated forged steel 1" shorter than stock kickstand Mounts to stock mount and accepts stock spring

Exotic Kickstand $139.99 Yana Shiki Exotic Kickstand Tough billet aluminum construction Sleek, custom design Sizing: Standard: Approximately OEM length Short: Approximately 1.5" shorter than OEM Length Lengths may vary slightly depending on model

Bolt - On Kickstand $124.95 Moose Bolt-on Kickstand Powder-coated steel shaft and sturdy ?” steel mounting bracket make a lightweight, yet heavy-duty stand Perfect for those unexpected rest stops along the trail Easy installation and removal with only two bolts (included) High-tension steel spring Made in the U.S.A.

Kickstand Kit $119.95 Trail Tech Kickstand Kit Custom designed side stands for both Enduro and MX style motorcycles. Strong, lightweight, and attractive Ultra-high strength chromoly mounting bracket Light weight, high strength forged aluminum stand Aluminum re-inforced high impact nylon foot at base of stand - no sharp edges! Custom designed for exact model fit - Installs in 10 minutes. No modifications required Go ahead - stand on the bike and kick it. Trail Tech kickstands are guaranteed to hold up to the riders weight Will not interfere with the riders boots. Will not fall down or bounce **Note: Image is for reference only. Product is bike specific and may vary from image shown.